Pins

A plumber in Fresno, CA assessed a bathroom drain line and confirmed saw cutting is needed. The work includes removing the vanity, opening FRP-covered walls, roughing in new plumbing, patching surfaces, and reinstalling fixtures. The plumber identified galvanized water piping and cast iron waste lines, indicating MegaPress fittings may be necessary.

A licensed plumber in Fresno, CA removed a cracked toilet and disposed of it. The plumber installed a client-supplied replacement toilet, then tested it to ensure proper flushing, sealing, and leak-free function.

A plumber in Fresno, CA completed a camera inspection of a sewer main line as part of an escrow inspection. The video was reviewed to evaluate the pipe’s condition and check for blockages or damage.

A licensed plumber in Fresno, CA repaired a leak at a saddle tap and a 90-degree fitting on a water storage tank. The plumber extended a short line with a coupling, sealed the connection with Teflon tape, and added a plastic ferrule to the leaking hose. The system was leak-tested for 30 minutes.

A plumber in Clovis, CA sealed the bathtub to stop water leaking from the bathroom into the bedroom during shower use. The technician applied caulk around the tub and asked the homeowner to observe the area for leaks over the next 48 hours.

A licensed plumber in Fresno, CA completed saw cutting and excavation to reach underground pipes. The plumber made three repair attempts, followed by camera inspections of the lateral and main sewer lines to evaluate their condition and detect remaining issues.

A licensed plumber in Clovis, CA tested an underground gas line from a propane tank to the house for leaks. The plumber replaced the ball valve at the house and retested the system to confirm proper and safe operation.

A Fresno, CA plumbing technician completed a kitchen set finish by installing and connecting faucets, fixtures, and sink plumbing, then tested all water lines to ensure leak-free operation and optimal flow performance.

In Friant, CA, a plumbing technician repaired a ceiling leak by locating the source, replacing damaged pipes or fittings, and pressure-testing the system. This ensured a leak-free result, protecting the home from water damage and preserving structural integrity.

A plumber in Sanger, CA cleared a clogged tub drain after multiple snaking attempts. The job involved diagnosing a non-functional drain lever caused by a missing tub drain piece. The technician verified proper drainage by filling and draining the tub. The old-style drain stop added difficulty to clearing the line.

A plumbing technician in Clovis, CA installed a water softening system. The technician rerouted existing water lines, placed the unit on a concrete pad, and tested for proper flow and leak-free connections.

A plumbing technician in Fresno, CA unclogged a toilet, cleared the blockage, and restored flushing operation. The technician tested the toilet to ensure it worked properly and had no leaks.

A plumbing technician in Fresno, CA installed an ice maker box and connected it to the existing water line. The technician tested the system to confirm it operated correctly and showed no leaks.

A plumbing technician in Fresno, CA rebuilt a vent line by replacing damaged sections and sealing all joints. The technician tested the system to confirm proper airflow and ensure no leaks.

A plumbing technician in Fresno, CA adjusted the toilet float to set the correct water fill level and cleared a blockage to restore flushing. The technician tested the fixture to confirm smooth operation and checked for leaks.

A Fresno, CA plumber from ABOVE ALL PLUMBING adjusted the toilet float to achieve optimal water fill levels, cleared blockages to restore efficient flushing, and tested the fixture for smooth operation and zero leaks, ensuring reliable toilet performance for homeowners.

In Fresno, CA, ABOVE ALL PLUMBING removed an old toilet and installed a new model, securely mounting it and connecting the waste line. The technician verified leak-free operation and confirmed proper flushing performance to ensure homeowner satisfaction.

A plumbing technician in Fresno, CA located a leak by cutting drywall, replaced a nipple and 90-degree fitting inside a valve, and installed a new chrome tub spout. The system was tested for proper operation. Drywall repair was not included in the service.

In Fresno, CA, ABOVE ALL PLUMBING installed a customer-supplied shower valve and trim, securely connecting all parts and performing pressure tests to ensure leak-free, reliable operation for long-term homeowner satisfaction.

A plumbing technician in Fresno, CA performed a hydro flush on a rain gutter system, removing debris and leaves to enhance water flow and prevent seasonal clogs during local rains.

A Fresno, CA plumbing technician used a 2,500 PSI hydro jet to remove grease and waste from the kitchen drain through the mainline. Post-service, mainline and lateral lines were tested to confirm clear flow and prevent future blockages.

A plumbing technician in Fresno, CA installed a new toilet, securely connected it to the waste line, and checked for proper flushing, tight sealing, and leak-free performance.

A plumbing technician in Fresno, CA cut tile to reach a faulty shower valve, removed it, and installed a new Pfister shower valve with a trim plate. The technician tested the system to confirm proper function and water flow.

A plumbing technician in Fresno, CA inspected a slow-draining upstairs tub. The drain was cleared of some hair using a snake. An outdated overflow cover that frequently jammed was replaced with a new chrome model. The customer was informed the tub cannot fully fill and accepted this. A follow-up visit is scheduled to discuss a bathroom remodel.

A plumbing technician in Fresno, CA identified a new location for a tankless water heater in the crawl space across from the water softener. The job includes constructing framing to suspend the unit and rerouting gas, water, and electrical lines to support the installation.

A plumbing technician in Madera, CA removed a clogged toilet caused by root intrusion. The toilet was not reinstalled because of a broken flange. The technician informed the customer of the damage and next steps.

A plumbing technician in Fresno, CA installed a tub, shower walls, shower valve, shower head, spout, and drain. The service included top-out plumbing and set finish. The technician tested all fixtures to verify water flow, function, and leak-free operation.

A plumbing technician in Fresno, CA used hydro jetting to clear buildup and debris from drain lines. The technician then completed a camera inspection to check for pipe blockages or damage.

A plumbing technician in Fresno, CA replaced a damaged main sewer line. The technician removed the old pipe and installed a new one from the house to the connection point. The updated system was tested for proper flow and confirmed to be free of leaks.

A plumbing technician in Clovis, CA replaced a backflow preventer and connected it to the water supply. The technician tested the system to confirm correct operation and compliance with safety codes.

A plumbing technician in Fresno, CA replaced the central control board, bled the gas line before startup, verified water heating function, and installed a gas drip leg to support safe and efficient water heater operation.

A plumbing technician in Fresno, CA completed rough-in, top-out, and final set finish work. The technician tested all fixtures and lines to confirm proper function, detect leaks, and meet project requirements.

A plumbing technician in Fresno, CA completed final work on a residential plumbing project. Tasks included rough-in, top-out, and finish installation. They tested all fixtures and lines to confirm leak-free performance, proper operation, and compliance with specifications.

A plumbing technician in Fresno, CA replaced a faulty tub spout and a leaking sink cartridge. The technician tested both fixtures after installation to confirm proper function and detect any remaining leaks.

A plumbing technician in Fresno, CA installed two backflow preventers and two protective cages. The service included excavation, concrete pad installation, equipment setup, and testing to ensure system compliance and function.

A plumbing technician in Fresno, CA replaced three commercial sink basket strainers and rebuilt the connected drain lines to improve sealing and water flow. The technician also flushed and inspected a tankless water heater to remove scale buildup and confirm efficient operation.

A plumbing technician in Fresno, CA inspected a damaged backflow test valve with broken threads lodged inside. The technician attempted to remove the stuck nipple but was unsuccessful. After notifying the customer, a new valve was ordered. Installation will occur once the replacement part arrives on site.

A plumbing technician in Fresno, CA removed an old toilet, inspected the waste line using a camera to check for blockages or damage, and installed a new toilet. The technician tested the new installation to ensure proper flushing, tight sealing, and leak-free performance.

A plumbing technician in Fresno, CA replaced a leaking lavatory faucet cartridge in the master bathroom. The plumber reassembled the faucet, tested the fixture, and confirmed it was working correctly without any leaks.

A plumbing technician in Fresno, CA installed two water softeners and connected them to the existing water supply system. The technician tested both units to verify water flow and checked for leaks to ensure effective operation.

A plumbing technician in Fresno, CA completed a full flush and diagnostic service on a tankless water heater. The service removed scale buildup, restored heating efficiency, and verified proper function. The technician tested the unit after the service to confirm performance and ensure there were no leaks.

A plumbing technician in Fresno, CA completed a full domestic water re-pipe, replacing old lines from the street connection to the water heater. The technician installed and connected all new water lines, then tested the system to ensure proper pressure, steady flow, and no leaks.

A plumbing technician in Coarsegold, CA installed four faucets and sink bowls, connected the drain lines, and ensured all fixtures functioned correctly. Each component was tested for proper drainage and confirmed to have no leaks.

A plumbing technician in Fresno, CA replaced a faucet cartridge, installed a dishwasher with a properly looped drain pipe, and inspected bathroom valve cartridges. The technician identified corrosion and sediment buildup in the piping and verified dishwasher function with a full cycle test. The customer reviewed component conditions and declined a sediment filter installation.

A plumbing technician in Fresno, CA inspected a bathroom shower and faucet for dripping issues. They checked the kitchen faucet for possible replacement. They also examined the hot water supply, which showed reduced flow, suggesting either pipe restrictions or a water heater problem.

A plumbing technician in Fresno, CA installed a new commercial sink by connecting to existing water lines. They relocated a three-compartment sink, rebuilt its drain, and added a new drain with PEX water lines and a shutoff valve. After installation, they restored water service and tested the system for leaks.

In Rialto, CA, ABOVE ALL PLUMBING performed a hydro flush on kitchen and mainline drains, removing buildup to restore optimal water flow and prevent seasonal clogs common in this area.

A plumbing technician in Fresno, CA completed the finish installation of a tankless water heater. The technician secured all connections, tested the system for leaks, and confirmed proper operation to ensure reliable performance.

A plumbing technician in Fresno, CA installed and connected hot and cold water lines using copper and PEX at a sink location. They capped the hot line, added a tee to the cold line, restored water flow, and installed a copper stub-out for a water heater.

A plumbing technician in Fresno, CA completed a tankless water heater flush and service. The work removed scale buildup, improved system efficiency, and restored proper operation. The technician tested the unit afterward to confirm full functionality and verify that no leaks were present.

A plumbing technician in Fresno, CA relocated a toilet by 46 inches. The work included breaking concrete, repositioning the closet flange, completing rough plumbing, and repairing the concrete after installation.

A plumbing technician in Fresno, CA completed a full home re-pipe, installing new water lines and two tankless water heaters. All five bathrooms and wet fixtures were replaced and reconnected. The system was pressure-tested to ensure proper flow and operation throughout the home.

A plumbing technician in Fresno, CA installed a backflow preventer at the Locan property. The device helps protect the water supply from contamination. The technician tested the installation to ensure it functioned correctly.

A plumbing technician in Fresno, CA performed a demolition cleanup that included removing drywall debris from a bathroom and closets, clearing shelves from a bedroom, taking out linoleum from the garage, and cleaning up garage trash as requested by the client.

A plumbing technician in Fresno, CA repaired a leak in the main water line and cleared a blocked floor sink drain. The technician snaked the line to restore flow, then tested the system to ensure there were no leaks and the drain worked correctly.

A plumbing technician in Fresno, CA installed a filtered water line to a faucet at a Starbucks during overnight hours. The technician completed testing to confirm proper water flow and filter function, allowing the business to operate without daytime interruption.

A plumbing technician in Fresno, CA rebuilt a kitchen waste line by replacing damaged components. They restored proper drainage and tested the system with water to ensure smooth flow and no leaks.

A plumbing technician in Fresno, CA installed and rerouted a 2-inch waste sewer line spanning 140 linear feet around the home to the front yard. The line was pressure-tested to verify optimal flow and prevent future blockages.

In Fresno, CA, a plumbing technician from ABOVE ALL PLUMBING installed a mechanical coupling on a stop to secure the connection. The repair was tested for leaks and stability, ensuring reliable, leak-free operation for homeowners.

A plumbing technician in Fresno, CA replaced a faulty T&S cartridge that was disrupting faucet function. After installing the new cartridge, they tested the faucet to confirm consistent water flow and no leaks. This service restored proper operation to the fixture.

A plumbing technician in Fresno, CA inspected the mainline waste system by running a camera through the cleanout and used a locator to trace the pipe’s path and assess its condition.

A plumbing technician in Fresno, CA completed a full flush and diagnostic service on a tankless water heater. The process removed scale buildup, checked all operating functions, and confirmed the system's energy efficiency.

A plumbing technician in Fresno, CA removed tile from a laundry room and bathroom. The technician cleared all debris and cleaned the areas, preparing them for the next stage of renovation.

A plumbing technician in Fresno, CA completed a hydrotankless flush service. This process removed scale and sediment buildup, improved system efficiency, and helped extend the lifespan of the tankless water heater.

A plumbing technician in Fresno, CA installed a Navien 240A2 tankless water heater with a dedicated recirculating line. This system provides on-demand hot water while improving flow efficiency throughout the home.

A plumbing technician in Fresno, CA removed drywall debris from three closets and behind a bathroom toilet, cleared shelves left in the bedroom, and disposed of linoleum and trash from the garage. The service addressed all onsite waste removal tasks requested by the client.

A plumbing technician in Fresno, CA removed drywall debris from three closets and behind a bathroom toilet, cleared shelves from a bedroom, and disposed of linoleum and trash left in the garage. This thorough post-demolition cleanup ensures a safe and clean home environment for residents.

A plumbing technician in Fresno, CA inspected a sewer line and found grease and sludge buildup. The technician recommended hydro flushing to clear the sewer and drain lines for improved flow and function.

A plumbing technician in Fresno, CA reinstalled a faucet and reconnected sink plumbing in a laundry room. The technician installed and connected a faucet in a guest bathroom. In a hall bathroom, two faucets, a shower trim conversion kit, a tub drain, and a shower armhead were installed using customer-provided fixtures. Labor and materials were included.

A plumbing technician in Fresno, CA reinstalled a laundry room faucet and reconnected the sink plumbing. In the guest bathroom, a faucet was installed and connected. In the hall bathroom, two faucets, a tub drain, a shower armhead, and a shower trim conversion kit were installed and connected. Fixtures were customer-provided.

A plumbing technician in Fresno, CA repaired a corroded galvanized water line, restoring proper water flow and preventing future leaks common in aging local pipes.

A plumbing technician in Fresno, CA broke concrete in a kitchen to reach and repair a damaged copper water line that had been accidentally struck and broken. The service restored water flow and prevented further damage under the flooring.

A plumbing technician in Fresno, CA performed a hydro flush targeting the kitchen drain but encountered blockages at multiple entry points. A follow-up camera inspection showed separate drainage systems for the kitchen and toilet. The technician identified severe rot buildup in the cast iron piping, indicating the piping is in poor condition.

A plumbing technician in Fresno, CA opened a wall behind a washing machine to replace an old cast iron drain with new PVC piping. They installed a cleanout for easier future maintenance. After reconnecting the washer, they ran multiple cycles to confirm proper drainage and ensured the system handled both hot and cold water without leaks.

A plumbing technician in Fresno, CA completed the set finish installation in a master bathroom. The technician inspected the lavatory sinks and recommended using longer drain assemblies to match the sink depth.

A plumbing technician in Fresno, CA removed concrete and flooring to access a blocked 2-inch cast iron floor drain. They replaced a damaged pipe section with PVC, installed a new P-trap and drain, cleared the line with a medium snake, reconnected the trap primer, repaired the concrete, and cleaned the area for flooring reset.

A plumbing technician in Fresno, CA installed toilets in Building 3, excluding two units awaiting new flooring. The technician completed shower trim installations in Building 3 and started the same task in Building 2. Trash removal was also completed across the site.

In Fresno, CA, ABOVE ALL PLUMBING's technician installed toilets in Building 3, except two units pending flooring completion. Shower trims were finalized in Building 3, with work initiated in Building 2. Comprehensive trash removal ensured a clean, safe site.

A plumbing technician in Fresno, CA replaced the central control board, bled the gas line before startup, verified proper water heating, and installed a gas drip leg. This service ensured the system operated safely and reached the correct temperature.

A plumbing technician in Fresno, CA inspected a bathroom sink to identify the source of a leak and gave repair recommendations based on the findings.

A plumbing technician in Fresno, CA cut into the drywall to access damaged plumbing and replaced the waste and overflow components. This service restored proper drainage and ensured the fixture operated correctly.

A plumbing technician in Visalia, CA used a camera snake to inspect the sewer vent for blockages or damage. The technician recorded video footage during the inspection and provided it for further analysis.

A plumbing technician in Fresno, CA installed a tankless water heater on a home’s exterior and relocated the gas line. The technician also connected a customer-supplied dishwasher, garbage disposal, faucet, and sink faucet. The project included both rough and finish plumbing work, using materials provided by the technician and fixtures supplied by the customer.

A plumbing technician in Clovis, CA installed hot and cold PEX lines for a new shower setup. The project included connections for a ceiling rain shower head and a diverter valve for a dedicated wand. The customer supplied the valve and trim kit. A tile-ready square drain was planned at the existing drain location.

A plumbing technician in Fresno, CA inspected a residential waterline cleanout in multiple directions toward the house and street. The inspection revealed several bellies in the line. Video documentation was captured and delivered for further review and assessment.

A plumbing technician in Madera, CA ran new water lines to connect a filtration system. This installation improved water flow and ensured the system operated correctly.

A plumbing technician in Fresno, CA installed a 90-degree fitting on a 3/4-inch steam drain line outside the master bathroom. The technician contacted the homeowner before entering the backyard to complete the installation.

A plumbing technician in Fresno, CA installed a 90-degree fitting on a ¾-inch steam drain line located outside a master bathroom. The technician informed the homeowner before entering the backyard to complete the work.

A plumbing technician in Kingsburg, CA completed a sewer line inspection using a camera snake. The technician provided the homeowner with a quote for installing a cleanout to improve access and maintenance of the sewer system.

A plumber in Clovis, CA installed a faucet valve in the correct upward position and recessed it fully into the wall. The technician documented the valve placement with photos to confirm proper installation and alignment.

A plumbing technician in Clovis, CA re-routed a 1 1/4-inch PVC water main from the meter to the right side of the home to improve water flow distribution. This service ensured reliable water delivery throughout the property.

A plumbing technician in Clovis, CA performed hydrojetting on a main sewer line to clear grease buildup. The service also revealed metal corrosion and debris caused by a deteriorating trap.

A plumbing technician in Kingsburg, CA replaced a damaged waste pipe section in the crawl space to fix a drainage issue. The repair restored the home’s plumbing function and prevented further water flow problems.

A plumbing technician in Grover Beach, CA removed an existing bathtub and prepared the space for a new 60 x 30 left-drain bathtub with white wall surrounds. The work included installing a tub spout, shower head, overflow, and drain as part of a scheduled property service agreement.

A plumbing technician in Fresno, CA found a pinhole leak in a 3/4-inch PEX hot water line. The technician identified the issue promptly to prevent further water damage and ensure the system's continued function.

A plumbing technician in Fresno, CA inspected a tankless water heater that had stopped working. The technician identified the issue and provided repair recommendations to restore proper operation.

A plumbing technician in Fresno, CA inspected a tankless water heater that had stopped working. The technician identified the issue and recommended specific repairs to restore proper operation.

A plumbing technician in Madera, CA performed a hydro flush in both directions on the main sewer line. This service cleared a blockage and restored normal water flow, helping to prevent potential system backups and maintain proper drainage.

A plumbing technician in Madera, CA performed a hydro flush in both directions on the main sewer line. This service cleared a blockage and restored normal water flow. An assistant supported the operation to ensure thorough cleaning and efficient drainage function.

A plumbing technician in Fresno, CA cleared a blockage in the garbage disposal to restore proper function. This service ensured water and food waste drained efficiently, preventing further kitchen plumbing issues.

A plumbing technician in Reedley, CA removed 34 soldered water lines and installed two 3/4-inch male adapters for IPS water lines. The technician added a 3/4-inch ball valve, reattached earthquake straps, refilled the water heater, ignited the flame, and set the temperature to setting A for correct function.

A plumbing technician in Sanger, CA removed a faulty septic pump and installed a new pump with a check valve. This work restored consistent flow and proper function to the septic system.

A plumbing technician in Fresno, CA performed hydrojetting to clean a storm line drain. The service cleared blockages and restored proper water flow. This process removed buildup to help prevent future drainage problems.

A plumbing technician in Clovis, CA repaired a flooded eyewash station to restore proper function and meet safety standards. This service helped maintain a safe environment and supported facility compliance with health regulations.

A plumbing technician in Fresno, CA inspected shower valve stems, examined running toilets, and identified the need for new fill valves. The technician also checked the dryer vent beneath the home to ensure proper function and safety.

A plumbing technician in Fresno, CA repaired a leaking pool water line at the rear of a home. The technician disassembled the union fitting, reseated the gasket, and reconnected the joint to stop the leak.

A plumber in Fresno, CA installed a customer-provided shower valve in an open wall. The technician routed piping through the attic and back to the valve to support future repiping without opening the shower wall.

A plumbing technician in Fresno, CA reset a toilet by installing new wax rings, bolts, and bolt covers to improve sealing and stability.

A plumbing technician in Fresno, CA completed plumbing services for a shower remodel. The work included installing new fixtures and preparing water lines to fit the updated layout.

A plumbing technician in Fresno, CA relocated a gas line using two MegaPress 90-degree fittings. This adjustment improved alignment and supported safe function for the system.

A plumbing technician in Fresno, CA repaired a leak at a hand wash sink. The repair restored proper function and stopped further water damage.

A plumbing technician in Fresno, CA replaced an under-sink water filter and worked to fix a jammed garbage disposal. The service focused on restoring proper water filtration and clearing disposal blockage for improved sink function.

A plumbing technician in Sanger, CA repiped the hot water lines to improve water flow and system reliability. This service addressed performance issues by replacing old piping with updated materials for consistent operation.

A plumbing technician in Sanger, CA completed fixture installation and preparation during a bathroom remodel. The work supported updates to the layout and ensured proper function of newly added plumbing components.

A plumbing technician in Fresno, CA installed a new shower pan and shower valve. The technician also repaired the subfloor using 3/4-inch plywood to provide a solid foundation for the installation.

A plumbing technician in Fresno, CA replaced a Moen cartridge to restore proper function to a plumbing fixture. This service resolved issues with water flow and temperature control, ensuring reliable performance.

A plumbing technician in Fresno, CA removed a damaged A&W laundry box by cutting into the drywall and replacing it with a new unit. The work restored proper water connections and improved laundry area functionality.

A plumbing technician in Madera, California repaired a pilot light to restore the proper operation of the unit. The service ensured the system functioned correctly and safely.

A plumbing technician in Fresno, CA repaired a refrigerator leak to restore normal function and stop further water damage. This service ensured the appliance operated correctly and protected surrounding areas from moisture issues.

A plumbing technician in Three Rivers, CA resolved a no-hot-water problem by repairing the water heating system. The service restored consistent hot water flow for the property.

A plumbing technician in Fresno, CA completed maintenance on a tankless water heater. The service helped maintain heating efficiency and prevent potential issues. Regular upkeep supports long-term system performance and lowers the chance of unexpected failures.

A plumbing technician in Fresno, CA replaced a damaged section of drain piping under the house. The work restored drainage and helped prevent future leaks. This service ensured reliable water flow and protected the home’s foundation from moisture issues.

A plumbing technician in Fresno, CA cleared a kitchen drain stoppage by running a 38-foot snake through the line. This restored normal water flow and resolved the blockage efficiently.

A plumbing technician in Clovis, CA completed a hydrojet service on a sewer system. One operator and one assistant used high-pressure water to remove blockages and improve flow through the pipes.

A plumbing technician in Fresno, CA installed new sink drains and reconnected a waterline to a new line. All components were tested and confirmed to work correctly, ensuring consistent water flow and proper drainage.

A plumbing technician in Clovis, CA replaced a Nuvo Manor cartridge to restore proper water filtration and ensure the system operated correctly.

A plumbing technician in Fresno, CA completed a hydro flush on the main sewer line to clear a toilet backup. The service restored proper drainage and improved flow throughout the system.

A plumbing technician in Fresno, CA installed approximately 100 feet of vent lines, covering 60% of the plumbing fixtures. The technician adjusted one section to fit around AC pipes, ensuring proper clearance and function without disrupting nearby systems.

A plumbing technician in Fresno, CA installed a new shower valve and opened drywall in the ceiling below to improve ventilation. This work supports safe moisture control and ensures proper access to plumbing systems.

A plumbing technician in Kingsburg, CA completed trench digging for new water supply and irrigation lines. The work included starting installation of risers and cleanout adapters to support ongoing plumbing system development.

A plumbing technician in Fresno, CA completed a sewer service to restore system flow and remove potential blockages. The work ensured wastewater could pass through the pipes without obstruction, reducing the risk of backups or damage.

A plumbing technician in Madera, CA connected a water softener system using 100 feet of 1-inch PEX. The installation included copper-to-PEX adapters, 90-degree elbows, Talons, a 1½-inch San Tee, no-hub couplings, and PVC pipe with fittings for the condensate line.

A plumber in Clovis, CA capped sink water lines and installed a new water line to an ice maker box. The technician shut off the valve on a 14-inch copper line at the saddle tap, restored water at the well, and secured PEX lines with Talons after checking for leaks.

A plumbing technician in Fresno, CA cleared a jammed garbage disposal and removed a small spoon that caused the blockage. The service restored proper drainage and ensured the unit operated correctly.

A plumbing technician in Clovis, CA fixed a tub valve that released water after shutting off. The issue stemmed from remaining water in the line. The technician corrected the hot and cold water supplies and advised the homeowners to drain the handheld wand before storage to prevent drips.

A plumbing technician in Kingsburg, CA completed a sewer camera inspection to check underground pipes for damage at locations scheduled for paving. The inspection was recorded to support further pipe condition evaluations.

A plumbing technician in Madera, CA completed an emergency repair on a broken water line in a newly built restroom. The job required core drilling to reach and replace the damaged section of piping.

A plumbing technician in Clovis, CA removed a 5-foot section of pipe and replaced it with new ¾-inch copper piping from the kitchen to the private dining area. The installation included a 90-degree drop into the wall to maintain proper alignment and flow.

A plumbing technician in Fresno, CA replaced the filter on a drinking fountain and bottle filler to maintain clean and safe water access. This service supports proper hydration in public or shared spaces by ensuring filtered water delivery.

A plumbing technician in Fresno, CA installed a leak detector and automatic shutoff device at the main water entry point. This setup helps protect the home from potential water damage by stopping the water flow if a leak is detected.

A plumbing technician in Fresno, CA installed condensate lines for AC units and completed the remaining water drops. The technician also reviewed the gas and water layout and ordered materials needed to finish both systems.

A plumbing technician in Fresno, CA replaced a damaged sewer line from the house to the street. The new pipe was installed at the correct elevation to improve flow and eliminate low spots in the system.

A plumbing technician in Fresno, CA replaced a broken garbage disposal at a kitchen sink. This service restored proper drainage and improved daily kitchen use.

A plumbing technician in Fresno, CA installed five drains. Three downstairs drains were raised and aligned with the concrete surface. Two additional drains were installed upstairs. This work improved drainage function across multiple levels of the property.

A plumbing technician in Fresno, CA completed a hydro flush on a sewer system. The service removed buildup and restored proper water flow. This process helps maintain system efficiency and prevents blockages.

A plumbing technician in Fresno, CA performed a hydro flush on a sewer system. The service cleared internal buildup and helped restore normal wastewater flow. This process supports consistent drainage and reduces the chance of future blockages.

A plumbing technician in Fresno, CA performed a hydro flush on a sewer system. The service cleared internal buildup and improved wastewater flow. This process helps maintain efficient drainage and prevents future blockages.

A plumbing technician in Fresno, CA performed a hydro flush to clear buildup from the sewer system and restore normal flow. This service improves drainage efficiency by removing obstructions using high-pressure water.

A plumbing technician in Fresno, CA performed a hydro flush on a sewer system. The service cleared internal buildup and restored normal wastewater flow. Hydro flushing helps prevent blockages and supports consistent drainage in residential and commercial systems.